‏إظهار الرسائل ذات التسميات Diesel engines. إظهار كافة الرسائل
‏إظهار الرسائل ذات التسميات Diesel engines. إظهار كافة الرسائل

الجمعة، 13 نوفمبر 2015

انواع البواجي و وضيفتها


انواع البواجي
أنواع شمعات الاحتراق او البواجي

هناك نوعين للبواجي :


1- النوع الأول عادي ذو راس واحدة ويختلف هذا النوع بإختلاف السيارة وتصميمها
وهذا النوع من فرعيين
هما الساخن و البارد 


2- وهناك ايضا نوع متعدد الرؤوس لتقوية الشرارة الخارجة منه وتاكيد الاحتراق 
وظيفة البواجي

هي عبارة عن وسيله لإشعال الخليط المتكون من البنزين والهواء داخل غرفة الإشتعال


علماً أن شمعات الاختراق تعمل تحت ضغط عالي

لان فيها قوة كهرباء عالي قادمة من الكويل 

وهنا يمكننا ماشاهدة رسمة تفصيلية لشمعة الاشتعال

في غرفة اشتعال واحده

اولا الخليط 
ثانيا ضغط الخليط الى اقصى حد
ثم الإشتعال وانزال البستم
واخيرا تفريغ الغاز بعد الإحتراق


اضف الى معلوماتك

ربما يستغرب البعض من ان شمعات الاحتراق تحتوي على السيراميك و لكنها كذلك لعدة اسباب منها
عزل قوة الشرارة وحصرها
ايضا السيراميك موصل غير جيد للحرارة و هذا شي جيد حيث يعمل على شكل عازل يعزل الحرارة و الكهرباء العالية
لذلك كلما زادت مادة السيراميك في الشمعات تكون الشمعات تتحمل حرارة عالية وتسمى شمعات الاشتعال الحارة 

الثلاثاء، 3 نوفمبر 2015

نظام الفرامل وأنواعها Air Brake System

نظام الفرامل وأنواعها
Air Brake System

لا تكفي القوة الناتجة من تجهيزة الفرامل الهيدروليكية لكبح المركبات الثقيلة بواسطة قوة السائق أو قوة المؤازرة, ولكن نحتاج إلى مصدر للقوة المؤثرة بخلاف السائق. ويمكن توفير ذلك عن طريق الهواء المضغوط, وتكون القوة المؤثرة على فرامل العجل تساوي ضغط الهواء مضروب في مساحة غشاء اسطوانة العجل. ويبلغ الضغط المانومتري في نظام الفرامل أما 5 أو 7 بار (0.5 إلى 0.7 ميجا بسكال- نيوتن/ مم المربع).
ويستخدم السائق ضغط القدم فقط للتحكم في دخول الهواء المضغوط لدائرة الفرامل للتأثير على بطانات الاحتكاك في فرامل العجل.
وتتكون دورة الفرامل كوحدة كاملة من جزئين رئيسيين. يقوم الجزء الأول بإمداد التجهيزة بالهواء المضغوط اللازم لها. بينما يحتوى الجزء الثاني على أجهزة التحكم في الفرملة وتشغيلها.
أجزاء دائرة الفرامل الهوائية المزدوجة

ويتكون جزء أمداد الهواء, من ضاغط هواء ومرشح هواء ذي وصلة لنفخ الإطارات ومنظم للضغط ومضخة للوقاية من الصقيع وخزان هواء وصمام للهواء الفائض وأنابيب وليات وأحيانا مرشحات لأنابيب الفرامل.
ويتكون جزء التحكم وتشغيل الفرامل من صمام بدال الفرامل (دعسة الفرامل), صمام الفرملة اليدوية, اسطوانة الفرامل, بالإضافة إلى مجموعة من الصمامات الخاصة في تجهيزة الفرامل الثنائية وفرملة المقطورة. 
ويوفر نظام فرامل الهواء قوة ضغط أكبر من قوة السائق تكون قادرة على إيقاف الكتلة الكبيرة للشاحنة, وفي نفس الوقت توفر من مجهود السائق في الضغط على البدال. وتتميز فرامل الهواء عن الفرامل الهيدروليكية بأنه ليس هناك مشكلة من ناحية التسريب لسائل الفرامل, وكذلك وسهولة توصيل فرامل الجرار (القاطرة) مع المقطورة.

المبطئات (المعوقات)  Retarders

المبطئ هو جهاز يعمل على تقليل الحمل على فرامل الخدمة الاحتكاكية لنظام الفرامل للسيارات الثقيلة. حيث أن الفرامل الاحتكاكية معرضة لظاهرة اضمحلال الفرامل بسبب ارتفاع درجة حرارة الأجزاء. وترتفع درجة حرارة أجزاء الفرامل بالسيارات الثقيلة نتيجة استخدام الفرامل الاحتكاكية لتوقيف الكتلة الكبيرة للسيارة. والتعرض لاستخدام المتكرر للفرامل مثل الحافلات داخل المدن. ولهذا السبب تجهز السيارات الثقيلة والحافلات بنظام إضافي للفرامل لا يعتمد على الاحتكاك.
والمبطئات لا يقتصر عملها في مركبات الطرق ولكن أيضا يمتد ليشمل السكك الحديدية.
تستخدم المبطئات لتقليل سرعة المركبة, والمحافظة على سرعتها ثابتة إثناء نزول منحدر. والمبطئات ليس بمقدورها إيقاف المركبة إيقاف تام, حيث تنخفض كفاءتهم عند السرعات المنخفضة. وهم في الغالب يقومون بخفض سرعة السيارة ومن ثم تقوم بعدها الفرامل الاحتكاكية بإيقاف السيارة. وحيث أن الفرامل الاحتكاكية في هذه الحالة لا تستخدم عند السرعات العالية ولا بمعدل عالي فإن هذا يزيد من عمرها التشغيلي, كما أن عدم ارتفاع حرارة أجزاء الفرامل وانتقالها إلى الجنط يزيد من عمر الإطارات كذلك. 
وتعمل معظم المبطئات عن طريق بدال الفرامل ففي المرحة الأولى للضغط على البدال تشغل المبطئات ومع استمرار الضغط على البدال تشغل فرملة الاحتكاك. ويمكن تفعيل المبطئات ذاتياً أو يدويا عن طريق ذراع. وقد تكون المبطئات جزء منفصل يركب بالسيارة, أو كجزء متكامل مع نظام ناقل الحركة.
وقد يستفاد من المبطئات بتشغيلها جزئياً عند بدأ الحركة للوصول السريع لدرجة حرارة التشغيل للمحرك في الأجواء الباردة.

فرملة المحرك Engine brake:
سيارات البنزين:
معظم سائقي سيارات البنزين يعرفون بما يسمي فرملة المحرك عند نزول منحدر. فهم يقومون بوضع صندوق التروس في نقله منخفضة, ولا يقومون بالضغط على بدال البنزين. ولا يحدث التباطؤ نتيجة الاحتكاك في المحرك (وأن كان له مشاركة), ولكن عند غلق صمام الخانق في شوط السحب, فلا يستطيع الهواء دخول الاسطوانة. ويحدث نتيجة لذلك تخلخل في كل شوط سحب بكل أسطوانة من اسطوانات المحرك, ويزيد تأثيره على العجل نتيجة التخفيض العالي في صندوق التروس عند النقلة المنخفضة. وبذلك يحدث التباطؤ للمركبة.
سيارات الديزل:
حيث أنه لا يوجد صمام خانق في محرك الديزل, فإنه لا يمكن استخدام الأسلوب السابق في عمل فرملة المحرك. ولكن قامت أحدى الشركات باستخدام فكرة فتح صمام العادم عندما يصل المكبس إلى النقطة الميتة العليا. وبذلك قبل أن يعمل الهواء المضغوط عمل النابض للمساعدة في دفع المكبس لأسفل يتم تسريب الضغط, وهذا يماثل أن المحرك يعمل كضاغط هواء, وحيث أن العزم اللازم لذلك يأتي من العجل عن طريق صندوق التروس ذو التخفيض العالي فإن ذلك يؤدي إلى تباطؤ المركبة. ويقدر مقدار القدرة التي يعمل بها المحرك لإبطاء المركبة بمقدار 90% من قدرة المحرك لبعض المحركات.  ويعرف هذا النوع لسائق السيارات الثقيلة بأمريكا الشمالية بفرملة جاك. من عيوب تلك الفرملة الضوضاء العالية التي تصدرها أثناء التشغيل, حتى أن البعض أوصىبعدم استخدامها بالطرق.

فرملة العادم Exhaust brake:
فرملة العادم أبسط في عملها من فرملة المحرك. حيث يوجد صمام بأنبوب لعادم. عند غلق الصمام يرفع الضغط في نظام العادم مما يدفع المحرك ليعمل بجهد أعلى خلال شوط العادم, وبهذا يعمل المحرك عمل ضاغط الهواء. وحيث قوة الضغط تأتي من العجل عن طريق صندوق التروس فإن ذلك يبطئ المركبة. وفي هذا النظام يجب أن تكون أنابيب الفرامل مصممة لتتحمل الضغط العالي, كما أن هذا النظام يوفر مقدار قدرة أقل لتبطئ المركبة بالمقارنة بالأنظمة الأخرى.

المبطئ الهيدروليكيThe hydraulic retarder :
هذا النظام يستخدم إعاقة اللزوجة بين ريش متحركة وأخرى ثابتة في غرفة مملوءة بسائل لعمل التباطؤ المطلوب. وتختلف أنواع السوائل فهناك المبطئاتالتي تستخدم سائل نقل الحركة, أو زيت منفصل, أو ماء.
المبطئ البسيط يمكن استخدام ريش متصلة بعمود إدارة ناقل الحركة بين القابض والعجل. ومن الممكن أن يداروا عن طريق تروس من عمود الإدارة. الريش تكون في غرفة بها مسافة ضئيلة بين الريش وجدار الغرفة الذي به ريش أيضاً في نظام نقل الحركة الأوتوماتيكي. عند الحاجة لتبطئ الحركة يدخل السائل أو الماء للغرفة وتعمل أعاقة اللزوجة إلى إبطاء المركبة. سوف يسخن سائل بالغرفة ولذلك يحتاج إلى وسيلة تبريد. ويمكن تغيير قوة التباطؤعن طريق زيادة مستوى السائل بالغرفة.
ويتميز المبطئ الهيدروليكي بالعمل بهدوء تام بالمقارنة بفرملة المحرك.  

المبطئ الكهربائي The electric retarder:
يستخدم المبطئ الكهربائي حث كهرومغناطيسي لتوفير قوة التباطؤ. ويتكون من جزء دوار مركب بأي من المحور أو ناقل الحركة أو خط نقل الحركة. وجزء ثابت مثبت بهيكل السيارة. ولا يوجد سطح اتصال بين الجزء الثابت والجزء الدوار ولا يوجد سائل أيضا. عندما يراد الحصول على تباطؤ, توصل لفات الأسلاك الكهربائية بالجزء الثابت بالبطارية, فتولد مجال مغناطيسي يعمل على توليد تيار حثي في الجزء الدوار مما يقلل من سرعته وبالتالي بالجزء المتصل به. الجزء الدوار مصمم بحيث يوفر التبريد المطلوب. ولا يكون هناك عبأ على نظام التبريد بالسيارة عند تشغيل المبطئ.

في السيارات المهجنة يستخدم مبطئ كهربائي للمساعدة الفرملة الميكانيكية ويعمل على شحن البطارية. وتستخدم الطاقة في البطارية فيما بعد لتعجيل السيارة (زيادة سرعتها).

ROTASYON CYLINDER LINER & PISTON . LTD. STI.

facebook: Rotasyon Liner Piston

How an engine works





ROTASYON CYLINDER LINER & PISTON . LTD. STI.
facebook: Rotasyon Liner Piston




الخميس، 29 أكتوبر 2015

Cavitation Damage to Diesel Engine Cylinder Liners

The rapid wastage, leading to ultimate failure, of ship propellers, pump impellers, and other components, as a result of the effects of cavitation is fairly widely experienced and recognized. What may not be so well known is that a specific mode of attack occasionally seen on the water-side surface of diesel engine cylinder liners may also result from the same basic cause.
Cavitation damage has been defined as the dynamic consequence of the hydro-mechanical phenomenon of cavitation, 1 which occurs when a liquid in motion is subject to forces at right-angles to the direction of flow, so that the cohesive strength of the liquid is exceeded leading to the formation of bubbles in those region which fall below the absolute vapour pressure. The bubbles are of only momentary duration and collapse at rapid rates of acceleration to produce shock waves of very high intensity, and the repeated collapse of the bubbles against a metallic surface gives rise to pronounced local damage. Although in many instances this action results in the ultimate production of cavities, the word “cavitation” describes the events which occur within the liquid and not the effect on the metal, i.e., the liquid cavitates with the production of cavitation damage.
Cavitation is generally induced by a rapid increase in the velocity of the liquid, as may arise from the sudden divergence of flow initiated by the presence of objects, or from vibration of adjacent metal surfaces. Cavitation from the latter cause can, therefore, occur when the liquid itself is in a relatively static condition.
A symposium on the subject was held in November, 1965, by British Rail Chemical Research Division, and the subsequent report 2has been largely drawn upon for this article which is a general survey of the subject illustrated by examples from our experience.
Damage to cylinder liners thought to be due to this cause takes the form of deep pitting of a honeycomb nature. It is restricted to certain specific locations on the waterside surface and is found principally on the thrust side of the cylinder liner, i.e., that subjected to the thrust from the piston on the firing stroke, and occasionally on the diametrically opposite, or anti-thrust, side — a typical example is shown inFigure 1 this being associated with ultimate perforation of the liner; a portion of another liner is shown in Figure 2. The pitting may extend for the full length of a liner or be restricted to the lower regions, as seen in the examples, and may in certain circumstances, as shown in Figure 2, result in disruption. In most cases the liner as a whole is relatively free from corrosion and rust deposits. The rate of development of the pits may reach 0.10 in. in 1,000 hours, whereas ordinary corrosion is only of the order of 0.002 in. during the same time. The extent of the pitting varies from engine to engine and may also differ on the liners of any one engine. Cavitation damage is more prevalent in engines in transport service, where speed variation is more pronounced, and the onset in some engines may be associated with the operation of reboring where a significant reduction in the wall thickness has resulted.













Fig. 1  Typical examples of cavitation damage in service.

Fig. 2  Typical examples of cavitation damage in service.

The cavitation damage of liners is considered to be due to vibration of the cylinder wall, initiated by slap of the piston under the combined forces of inertia and firing pressure as it passes top dead centre. The occurrence on the anti-thrust side may possibly result from bouncing of the piston. In the laboratory it has been possible to reproduce the effects of cavitation by vibrations induced by ultrasonic or other transducers.
Although cavitation damage appears to result basically from a mechanical cause, the exact mechanism is not entirely clear and two schools of thought have developed, one supporting an essentially erosive, and the other an essentially corrosive, mechanism and thus the terms “cavitation erosion” and “Cavitation corrosion” have arisen to describe the effect. With the former, it is considered that shock impact on the metal surface produces local stresses in excess of the fatigue limit of the material. Cracks develop and, ultimately, small particles of metal become detached. The fact that cavitation damage can be produced experimentally in materials such as plastics or glass tends to support the view that it is an entirely mechanical phenomenon, as does the evidence that it can also be produced in non-electrolytic environments. On the other hand, there are aspects that lend support to the corrosion hypothesis. It is considered that the impact forces may only serve to remove the protective oxide film normally present on the surface, and that the hare regions thus produced become anodic to the remainder and local corrosion cells are set up, the anodic regions suffering a preferential attack. In addition, the existence of regions of differing stress levels, or zones of cold work resulting from the impacts can also result in small anodic areas. Further, variations in the flow rate over the surface result in different rates of oxygen diffusion and could also promote local corrosion.
Microscopical examination of sections cut from pitted regions of liners affected by cavitation damage show that the relatively mechanically weak phosphide eutectic is often left proud, in the pits. The examination of several pits which developed in the liner shown in Figure 1 showed this feature, as is evident from Figure 3. If erosion was the major factor it is considered that the eutectic should be preferentially removed. This fact, together with the observation that the corrosion products remain in the cavities, suggests that cavitation damage may be due to a mechanism which is primarily of a corrosive nature. It would be reasonable to assume that cavitation results from a combination of these processes, thereby accounting for the fact that different effects are found in different circumstances.

Fig. 3  Section through pitted region showing eutectic standing proud. (×400).

R. W. Wall, in one of the papers in the symposium previously mentioned, refers to laboratory experiments, the results of which indicated that corrosion at metal surfaces is accelerated by vibration and, in the case of iron in water, corrosion occurs in the form of isolated pits rather than in a uniform manner, suggesting that pitting could occur as a result of cylinder vibration only and may not necessarily be a consequence of cavitation in the water. Once pits develop, one would expect them to develop at a fairly rapid rate, due to the combination of a small anode and a large cathode. It is also thought that vibration increases the access of oxygen to the corroded surface, this being utilized in the cathode reaction to reduce the polarising action of hydrogen.
Damage to other portions of liners, that which is seen in the piston ring grooves, under flanges, or on the portion adjacent to the lower scaling ring (as seen on the liner shown in Figure 1) is considered to result, not from cavitation, but from differential aeration-a more common cause of corrosion, particularly where stagnant conditions may obtain.
Measures to prevent, or reduce, cavitation damage. should be considered firstly from the aspect of design, attention being given to methods of reducing the amplitude of the liner vibration. Piston slap can be reduced by minimizing the clearance, but attempts to reduce this too far could result in scuffing and increased wear. Other workers have suggested the use of a cam-ground piston with this end in view. Much greater success in reducing the severity of the piston impact has attended work done by the Admiralty Research Laboratories, using a specially designed piston incorporating an annular belt of oil between upper and lower rings, the oil acting as a viscous damper to cushion the motion of the piston and eliminating the tilting at the ends of the stroke.
In certain circumstances it may be possible to alter the design of the liner. In severe cases, longitudinal ribs can be employed or an additional support provided at about the mid-length, in an attempt to avoid resonant conditions. Measures of a palliative nature can be introduced by surface treatment of the liners, and in this respect the use of hard chromium plating or chromium plating on nickel has been found to be effective in certain conditions. Sprayed metals or the use of a ceramic coating based on alumina, applied by flame-spraying, have also been recommended. Other workers favour a resilient coating, such as nylon, but with materials of this type it may be difficult to effect a satisfactory bond and the attendant effect on heat conductivity must also be considered.
Attempts have been made to reduce the severity of attack by attention to the environment. Inhibitors, such as chromates, benzoate/nitrite mixtures, and emulsified oils, have been tried with varying success. Unfortunately, some inhibitors may not be suitable for use at temperatures approaching 100°C. and others may break down under conditions of cavitation; organic compounds, for instance, may be degraded and lead to precipitation.
Cavitation damage tends to fall off as the temperature is raised and, in one case, damage which was shown to be at a maximum at 50°C diminished significantly at 80°C. Raising the temperature of the cooling water is stated to be effective where anti-freeze additions based on ethylene glycol are employed.
Attempts have been made to reduce or prevent cavitation damage by the application of cathodic protection, and this has been found to be effective in certain instances of trouble on propellers. Its application to cylinder liners, however, is particularly difficult, and it is understood that no large measure of success has been obtained. Its effectiveness in any situation must be related to the particular parts played by the electrochemical and the mechanical factors in the case. The fact that cathodic protection has been found to be effective in counter-acting trouble with ships propellers, supports the view that cavitation damage results primarily from an electro-chemical, rather than a simple mechanical cause.
Little success has attended efforts to obtain relief by changes in the type of material. Iron with a higher elastic modulus should assist in reducing damage by modifying the vibration characteristics of the liner. More corrosion-resistant irons alloyed with chromium and nickel would possibly show an advantage, but unfortunately they possess inherently poor wear resistance.
Among other measures that have been advocated is pressurization of the cooling system, and this has effected a cure in certain cases experienced by the French Railways, possibly by preventing the formation of bubbles. It has also been suggested that it would be beneficial to remove the electrochemical factor entirely and to employ fuel oil as a coolant, but obviously a modification of this nature could only be adopted in certain instances.
In one case within our experience, corrosion in a six-cylinder diesel engine driving a small locomotive showed itself on cylinders Nos. 2, 5 and 6 after three years' service. After a further year, the No. 5 liner had to be replaced. The replacement gave only one further year's service, and the new one which was installed showed slight pitting after three months or so. The affected portion of the liners was in all cases adjacent to an internal rib on the engine frame as shown in Figure 4 and it is presumed that the trouble was associated with local turbulence, resulting from restriction in the water spaces. A slight attack was also shown on the frame itself in this vicinity. In this case, a 1% emulsified oil was added to the cooling water, which was also made alkaline, and no recurrence of the cavitation was seen during the subsequent six years.

Fig. 4  

In diesel engines trouble from cavitation damage is also found in coolant circulating pumps, main and big end bearings, and in the fuel injection equipment. With bearings, damage is thought to result from flow-induced cavitation, while in pumps and injection equipment it is associated with violent fluctuations that may occur when the flow is suddenly interrupted, It is found mainly in unloaded areas of bearings where the oil film pressure is low and, therefore, results from a cause different from that responsible for the more usual type of failure shown by these components. Its occurrence can be minimised by design changes, so that the oil pressure is maintained, or possibly by a change in material, a tin-base babbitt being more resistant than a lead-base alloy of the same hardness.
In conclusion, it would appear that the precise cause of the type of damage described is not yet known with certainty. Although-it is often ascribed to cavitation within the cooling water the evidence is largely of a circumstantial character based on the similarity between it and the damage shown by propellers and pump impellers. It is fairly certain that it stems basically from vibration of the liner, but whether or not mechanical forces are the primary or only factor is still a matter of doubt. With regard to alleviation of the trouble, it would appear that if the severity of either the mechanical or electrochemical factors is diminished, then the cavitation damage as such may be reduced to more tolerable proportions.

References

  1. Corrosion/Erosion—Maritimer; Anti-corrosion, Volume 14, No. 2, Feb. 1967.
  2. Cavitation Corrosion and its Prevention in Diesel Engines, Symposium Alexandra Palace, London, 10th Nov. 1965, British Railways Board.


Best Regards,
ROTASYON CYLINDER LINER & PISTON

الأربعاء، 28 أكتوبر 2015

What is cylinder liner ?

A cylinder liner is a device that is pressed into an engine block and houses the piston. It is much harder than the engine block and prevents the piston from wearing through the cylinder bore. Typically used in aluminum engine blocks and diesel engines, the cylinder liner is either pressed into position or held in place by the cylinder head. In large engines such as the engines found in diesel locomotives, the liner is part of an assembly containing a new piston, piston rings and a connecting rod and is changed as a complete unit during scheduled maintenance or repair.
In aluminum engine blocks, the block material is much too soft to house a piston. The friction of a piston moving up and down inside the alloy block would soon wear out, resulting in a loss of compression and severe oil consumption. The steel cylinder liner is pressed into the engine block and then the engine block is machined to assure that the cylinder head mating surface is smooth and flat. By machining the engine block to receive a steel liner, the engine is able to operate for many years without engine failure.
The flat surface resulting from the machining of the engine block assures a proper seal of the head gasket between the cylinder head and the engine block. An improperly sealed head gasket will result in over-heating of the engine, loss of power, and the potential to ruin the block and cylinder head. Great care must be taken when installing a cylinder liner into an aluminum engine block since the aluminum block will react to heat at a different rate than the steel cylinder liner. Improper fit at installation could result in a broken liner or a cracked engine block.
There are also instances when a cylinder liner can be used to repair a cast iron engine block that has suffered a catastrophic failure to a cylinder wall. Often, when an engine fails or "blows up," the cylinder wall takes the brunt of the trauma rendering it unrepairable by over-boring. In this instance, the block might be machined to receive a liner and then all of the cylinders could be over-bored to the same size, rendering the engine useful once again. For street driven vehicles, this is a viable option which typically offers the vehicle owner a significant savings over the cost of a replacement engine

there are a lot of Famous brand in this field, field of engine

manufacturer like Deutz and volvo and Scania and we can't forget Mercedes ....etc
.
Hello  ,

We are Rotasyon factory, one of the leader manufacturers in Turkey.

We produce high quality cylinder liners and pistons.

We also produce water cooled and air cooled cylinder liners.

Water cooled cylinder liners for: Mercedes-Benz , Volvo , Saab-Scania , Fiat-Iveco Man, Kamaz,

Zetor,Ursus, Leibherr, Caterpillar, Cummins, Komatsu,etc.

Air cooled cylinder liners for: Deutz, Hatz, Lombardini, Atlas, Copco, MWM, Lister, Eicher, R.Berliet,etc.

We export our products to a lot of countries in Middle east , and Europe

On the other hand we specialized in manufacturing piston and cylinder liner of Tractors like (Deutz , MWM , Güldner ,

Hanomag, Eicher , Zetor, Ursus, etc…) , And  piston ,cylinder liner for Generators and Heavy Machine
                                                         
And we can manufacturing special size or model of cylinder liner and piston (our customer like he want )
  
We have awarded quality certificate issued by Turkish standards institution and also our company has TS EN ISO 9001:2008 certificate.

For most of our parts, we get the certificate TS16949.

Our company deal with diesel parts (trucks – tractors - Electric generator ) more than 15 years.

Cover: Cummins, Perkins. Deutz, Mercedes-benz, Isuzu and Howo